If you’ve ever wondered how to get your laptop fixed at home, then you’ve come to the right place. You can follow these steps to replace your screen: assemble the tools you need, prepare a flat surface, and have all of your tools ready at hand. To begin, turn your laptop off and remove the battery. You should do this to prevent other problems from arising when replacing the screen. The screws that hold the screen in place are typically covered by stickers on the screen bezel. You’ll find them near the hinges when the display is open.
Installing a New LCD Panel
The first step in installing a new LCD panel is to remove the old one. Most modern laptops have LCDs that screw into the bezel with two small screws. Carefully remove these screws to allow you to access the LCD panel. Remove the screen carefully from the laptop, being careful not to damage the video wire or break any glass or plastic. Next, connect the new screen’s video connectors to the back of the computer. If necessary, apply adhesive tape to secure the connection.
To install a new LCD panel for laptop screen repair at home, start by removing the mounting brackets on the lid of the laptop. Locate the LCD’s cable connectors. Some LCDs have two cables, while others may have just one. Look for the model number on the LCD manufacturer’s label. You can use the model number to match the new panel to the old one. Once you have located the cables, disconnect the power cord.
Removing the Screws
Remove the screws that secure the screen bezel. Some are located in the corners of the bezel. Then, slide the new screen onto the back cover of the laptop. Be sure to apply light pressure to the digitizer cable. After you’ve removed the screws, you can align the LCD panel with the rest of the laptop’s components. Don’t forget to reconnect the inverter cable and the battery before you move on to the next step.
A new LCD panel is relatively inexpensive and may be your only option if your laptop’s screen is broken. The repair process can save you between $40 and $100 if you’ve worked on computers before. Using a technician online or doing the repair yourself could save you a bundle compared to sending the laptop off to the repair shop. However, it’s important to note that a DIY screen repair could be damaging to your laptop and may void the manufacturer’s warranty.
The first step in laptop screen repair is to check the damage to the display. If it’s too damaged, it’s best to replace it with a new one. In the event that you are unable to do so, follow the steps listed below to install a new LCD panel. There are no special tools or equipment needed, and the whole process should take about an hour. Once you have followed these steps, you should have your computer working again in no time.
Next, you should remove the bezel from the laptop screen. If there are screws underneath, you should remove them with a screwdriver. You can then remove the screen from the laptop case. Be careful not to damage any of the components during the process, as you must reconnect the power source and check the screen’s display to ensure it’s working correctly. You can also use the spudger tool to pry the screen out of the laptop case if it’s not attached properly.
Reinstalling Bezel
Remove the bezel on your laptop’s screen. The bezel secures the LCD screen to the laptop. To remove the screen, unscrew the two plastic brackets on either side and lay them on a flat surface. Be careful not to pull the screen too hard, as it can damage the video connectors. Carefully reconnect the video cables to the back of the new screen. Attach the bezel back onto the screen.
Replace the inverter screw, if present. Once you’ve done that, insert the new screen into the lid. Make sure that the dimensions and connectors match. Then, reinstall the bezel and replace the battery. To check the new LCD panel, you must perform the calibration procedure. After the calibration process is complete, the computer will shut down. Ensure that the new LCD panel is working properly before replacing the bezel.
Remove the bezel screws from your laptop screen. These are typically located near the LCD panel. Remove the screws and place the bezel components into a plastic bag. Do this a couple of times to ensure that you don’t miss any. It will save you time and frustration. The screen and bezel are attached with a thin plastic bezel, and this can make the process even easier. It may be necessary to remove the LCD panel first.
You may also have to remove the cover from the screen. You may find that it is cracked in the cosmetic area. If that is the case, you may opt to accept the cosmetic crack and purchase a new screen. It’s up to you whether to accept the cost of replacing the bezel or not. It’s a good idea to put the battery back in your laptop after replacing the bezel. The screen should look as good as new again.
Once you have removed the bezel, you will need to remove the screws that hold the screen in place. You may need a box cutter or hobby knife to cut these screws. Make sure you remove all screws underneath the covers. If you are replacing the LCD panel, you should carefully check to make sure the replacement screen matches the existing one. Also, be sure to follow the manufacturer’s warranty policy. The warranty on the screen can be voided if the replacement is not performed correctly. If you want to save yourself some time, a DIY guide might be all you need.
You may have to pry the display bezel off the side of the display. Be sure to use a special tool that can safely pry off plastic parts. If you have a small scribe tool, it will be easier to cut through the plastic. A putty knife or plastic flathead screwdriver will also work well. This way, you’ll be less likely to damage the glass. However, be sure to remove all screws before doing any of the rest.